![Narrated: Vise Drill Anvil [Restoration]](https://saketami.com/storager//46/d6/46d6b424bb31235a811449c863b00d9420c0b625c0168e64731cf8430dcffe85.jpg)
Narrated: Vise Drill Anvil [Restoration]
Added 2020-09-09 02:13:08 +0000 UTCThis is too many things.
Comments
https://marvelcinematicuniverse.fandom.com/wiki/Shotgun-Axe
Peter Laws
2020-09-13 05:17:30 +0000 UTCI've watched this a couple times ... all I can think of is Acting Director of S.H.I.E.L.D. Mac's Shotgun-Axe. (nice restoration as always!)
Peter Laws
2020-09-13 05:16:46 +0000 UTCOnly $4.10 new! (According to Pinterist) That's without the drill bits.
2020-09-10 21:09:45 +0000 UTCI was sitting here and thought I'd watch some of the videos that I've already watch...no, no life...and realized "FINE! We get the hint...where can we buy you pin-stripping stuff?" Make an Amazon wish list or something, already. ;-)
Brian Myers
2020-09-09 18:26:50 +0000 UTCYes, this is the upgraded sexier version for sure. Some were attached to forges as well.
Hand Tool Rescue
2020-09-09 17:52:45 +0000 UTCThe bronze chain is what I had in stock. I should fine a smaller brass one though.
Hand Tool Rescue
2020-09-09 17:51:52 +0000 UTCGood stuff!
Brian Myers
2020-09-09 17:34:05 +0000 UTC+1 for the japanning on this one. Very nice.
2020-09-09 16:38:01 +0000 UTCTHIS! This must be a thing.
Gene & Linnea
2020-09-09 16:33:22 +0000 UTCAnd, in a very amusing synchronicity, one of the sellers I follow on eBay recently listed this beast: https://www.ebay.com/itm/Stewart-Handy-Worker-machinist-vise-drill-anvil-collectible-blacksmith-tool-/383712023203. It's like this one except bigger and with even more stuff, including three-speed gearing for the drill bit, and separate pipe jaws for the vise. What I find fascinating is that this implies there were at least two companies making these!
Brooks Moses
2020-09-09 11:36:22 +0000 UTCFREEBIRD! Loved that. My only question for today, is that since you developed your own technique of Japanning, should this new finish not be hereto referred to as “Saskatooning?”
Marc McKenzie
2020-09-09 05:06:56 +0000 UTCThat’s pretty nifty. Too bad you can’t put one of those electromagnets on the back of the drill plate to hold the steel on there firmly, kinda like some matching tables. Well done on the restoration, though I have to ask. Why use the over-sized chain? Why not something similar to what was on it?
Sphynx
2020-09-09 03:36:33 +0000 UTCWow. So that's a thing. The japanning looks particularly good on it, though!
Brooks Moses
2020-09-09 03:20:52 +0000 UTCInteresting tool! Thanks!
2020-09-09 02:36:39 +0000 UTCMUAHAHAHAHA!
Hand Tool Rescue
2020-09-09 02:19:48 +0000 UTCIt is 4am over here and that music just freaked out every bone in my body. I'm not sure your soothing voice can calm me down after this ..
dreamer
2020-09-09 02:18:34 +0000 UTC
