Flowrednow

in metal this time

okay now its officially done, the model ive released prints well on internet print services for making metal parts.

i always see cages as armor and not a submission thing, thats just my perso...

its finally over

new desk toy ready to sit next to my translucent blade wolf, gem renamon, and my egg plane

i did end up switching back to automotive paint, which means its unwearable but i never made it to b...

okay, okay, okay

i just put a bunch more clears on it, you can only notice the blemish if you stare directly at it now

2025-06-27 00:55:15 +0000 UTC View Post

another slow update and abandonment of the cage project

i legit fucked this up today

one side looks amazing, but another side dripped and i tried to patch it up but to no avail :(

2025-06-22 20:00:41 +0000 UTC View Post

finally some progress

i have been working away at this and here is the result of the test pieces i made

...

x-2 comm

for selenes over on bluesky

pausing for a month because i hate epoxy

i really want to get this cage done properly and the last epoxy coating didnt work so i am going to try ONE last time. it has taken me 3 actual days of sanding to get all the epoxy off but i am set...

i dont think epoxy is the way to go

i completely redid the test ring. this time i waited till the epoxy was almost set till i dipped and brushed it on and it still left clean spots where the epoxy just dripped away. absolutely infuri...

hard lesson learned

wait for the epoxy to start setting before just painting it on and leaving it, it will drip from undersides and leave them pretty bare

now i gotta sand the epoxy off the test ring and try aga...

test pieces ready for epoxy

i didnt bother to sand or fill these perfectly unlike the aeromorph and its ring. they got a light coat of gold each and i will epoxy the ring tomorrow as a test. if all goes well i should have EVE...

Small update and change of course for my cage project

after a few suggestions, thinking it through, and a lot of consideration i decided to scrap my first test pieces which were done using clear coat and am making some new test pieces to try epoxy res...

final stretch

wet sanding the inside and outside, once it dries it gets one more 2500 grit sanding, a washing, then wet sanding, then washing then PAINT! then im debating between clear enamel paint or clear epox...

Plane in the spray booth

plane polish

sanding, spot fixing, the redneck drying box, and polish for use on planes

Oops, im not very good at this

i flipped the ring over before the clear was fully cured, and it ripped a chunk off the bottom. so im taping to try and fix it aaa

2025-03-25 18:54:29 +0000 UTC View Post

just stuff from today

little bit of an update

im working on a howto to finish up 3d prints, ive been learning alot about primer and paints and such working on finishing this 3d printed cage.

i got two comms coming up soon to share, more ...

test print

finally got around to dehyrdating a spool of plastic and test printing this, after about a day of sanding its very smooth and i just gotta procure some filler to fill the last imperfections out. 2025-03-10 03:55:38 +0000 UTC View Post

Cookies 2k

Cookies 4k

preview: another couple versions incoming

so yea, getting this situated for those that like some cookie

Suck it (2k)

back on my blade wolf shenanigans for today

thank you for your support

Suck it (4k)

blade wolf is back :)

thank you for your support

suck it wip 2

changed the pose up a bit to make it better.

suck it (wip)

back on my bw shenanigans :) should be done early next week.

Aero Cage Model STLs

thank you again for your support

Aero Cage Model .Blend

thank you for your support

edit: added the stls

Model Release info and renders

The two highest tiers get different packs.

Platinum: .Blend and STLs

Gold: untextured STLs

Silver will get a discount on the model if i can figure out this patreon shop thing.

model should be up here later tonight or early in the morning

btw a heads up with this model

i dont have the time and my 3d printer hasnt worked since the hurricane mess to actually print and test any functionality. it is 100% meant as just a desk ornament or something to use in 3d softwar...