Mouse trap - humane - catch and release
squirrelf3d posts
Comparing ADXL345 nozzle mounted vs top mounted
On discord @thisiscam mentioned that nozzle mount are usually more accurate (less bias) but also more noisy (more variance)
After testing one nozzle mount he found that it wo...
2023-06-14 03:33:41 +0000 UTC View PostApollo Update - May~JUNE 2023
For those not on discord I realized that I haven't really posted the list of updates done to the Apollo lately. And even for those on discord, the incremental tweaks may have gotten lost in the thr...
2023-06-10 05:10:05 +0000 UTC View PostEnder3pro/v2 Case - MantaM8P - made by George aka GxG
Courtesy of George aka GxG on discord, he enjoyed the community on discord associated with my patreon so much that he is pre-releasing this design here. 2023-06-07 04:11:16 +0000 UTC View Post
ApolloHeavy - dual 5020 (linear rails)
Currently only for Spider Pro v3, orbiter 2.0 , but can be adapted, by request, to any currently supported ApolloLander hotend.
Need new backplate new main body and new ducts, Apol...
2023-06-05 05:31:06 +0000 UTC View PostApolloExoslide - Ender5
Consider this Beta until tested and making sure holes align up on the under side
Currently only Mosquito Magnum & orbiter2.0 (+bowden option), but I now...
Klipper but really Moonraker - Relays and Buttons
If you want to control your printer PSU or leds with a relay and optionally with a physical temporary switch button. Here is some info I found and compiled
First, what not ...
2023-06-02 01:12:41 +0000 UTC View PostOrcaSlicer 1.6.3 update fix how to
As those of you on discord know, I'm using Orcaslicer these days
----
For those that don't know about OrcaSlicer, it's based on BambuSlicer which itself is based on PrusaSlicer. SuperSlicer ...
Apollo CoreXY model (ender5 with mercury zero G mod)
- Rapido (+ orbiter2.0)
- Mosquito (normal and magnum with sherpa mini)
This is based on the latest Apollo...
2023-05-29 22:23:03 +0000 UTC View PostBox for Lever Nuts Wire Connectors
This was a request, I don't have those in hand, they seem very handy as an interface between the printer board and the printer
This also could be use to cram in regular connector...
2023-05-10 03:35:01 +0000 UTC View Post120mm fan cover grill
Make sure you have a good clean surface and perfect mesh before printing, as the first layer is intricate.
6mm thick, with 4mm clearance between fan and grill.
Use regular self tapping sc...
For RC cars - ARRMA 40mm Motor - 4010 & 4020 dual fan mount
UNTESTED for now, will update when tested
--------
As long as you are a patron, feel free to sell printed version of those (please don't distribut...
2023-04-28 21:31:10 +0000 UTC View PostHi and welcome here:
First of all thank you for your support, without it most of these project would remain in their infancy and limited to my printer setup, some project would not even exist.
The shop page has ...
Nozzle Cam - full Apollo integration (Rev7 of the mainbody)
The Nozzle cam PCB can now conformably be installed behind the left fan.
This will be Rev7 of the main body (I'm exporting each hotend model for it, but should be done in a couple days)
M...
Cable chain Rev2 (Slightly Updated cable chain setup)
- The last piece of the X chain which is printed, has a screw at an angle which makes it easier to install/remove even with cables installed. This is the "major" upgrade to this 2023-04-07 20:00:26 +0000 UTC View Post
X axis tensioner for extended X move
Rev 2 mostly just makes it easier to install the inner sled (especially the printed ones which have tighter tolerance). No need to replace it with rev1 if you have it installed.
Also added a...
Brick Case Screen (BTT PiTFT 70)
This is now fully usable, and a few tweaks, now support for both heat inserts (4.6 and 5mm OD) increased the screen hold depth by 1mm so should be more flush
2023-03-30 19:09:09 +0000 UTC
View Post
Beacon3D scanner probe - Apollo and Apollo mini (req: X linear rail)
New probe with ultrafast mesh, and no contact. There was interest, took the gamble of buying it, not knowing if it would work with this setup or not. But it did!
If you want to get it, make s...
2023-03-21 00:32:45 +0000 UTC View PostBelt ends
Different types that I quickly made and used to attach the belt.
(this is what I used to install the new belt for the new Y tensioner that bring back full Y printable area)
print at 0.2mm...
Early testing only for now - versatile X motor block for wheel setup
This is an early test to make sure all fits.
I don't have a stock wheel setup anymore, so I can't test it.
Most important is making sure the endstop is far out enough for Apo...
2023-03-02 05:32:55 +0000 UTC View PostY Axis tensioner for 4040 ender3v2 or 3pro ( new model added ) - gain Y printable surface back to full print surface on rails)
----
Update:
With replacement belt ( needs to be slightly longer than stock length ) I was able to get the full Y printable surface back all 235mm front edge to back edge.
Use the...
2023-02-28 04:58:11 +0000 UTC View PostSunlu coupler - M6 pneumatic coupler
This actually took many tries to get it solid, but that one has held up over time, print orientation was key
I recommend PETG for its elasticity over PLA
print with at le...
Reverse Bodwen (rail setup only) - uses mini pneumatic clips
I will see if I can make a new X motor mount for wheel setup that can accommodate the same thing
Apollo Mini (dual 4010)
Finally finished it. (and thanks to KtotheStank for testing it)
I made it so that I can relatively easily convert any Apollo currently supported hotend into one of these. So feel free to sub...
Dual 5015 PWM (4 wires) fan - 24v - no more PWM noise
Took the gamble of ordering a couple 4wire Sunon fan (no idea if it's genuine or not, but it feels and sounds great.)
And it paid off. It's so much better and very quiet at low RPM with no PWM n...
Potential cable holder for single Z routed to the right side
This is a bit specific, but can come in handy for such setup.
Meant to hold your X gantry cable bundle routed to the right side.
Simple thing, two parts, secured with a single threade...
$5 Endoscope on Rev4 of the main body/ducts of the Apollo
-----
This is for REV4 and 5 of the main body only
working on a new setup for the rev6...
Bambulab hotend on Apollo - high quality and cheap
edit: thanks to Sethro_ who contacted bambulab we have the following info "Resistance is 100kΩ@25℃(±1%) and B-value is 3950K@25/50℃(±1%)"
Beefier belt holder for Apollo
update:
the backtrace didn't fit (would hit the frame), so reworked it, kept the overall length the same as when installed without a brace, so should fit perfectly now.
one mo...